Design and Implementation of a Planar Transformer with Fractional Turns for High Power Density LLC Resonant Converters


 Xu Robert
 25 days ago
 Views:
Transcription
1 Design and Implementation of a Planar Transformer with Fractional Turns for High Power Density LLC esonant Converters YuChen Liu, Senior Member, IEEE, Chen Chen, Student Member, IEEE, KaiDe Chen, Student Member, IEEE, YongLong Syu, Student Member, IEEE, DeJia Lu, Katherine A. Kim, Senior Member, IEEE, and HuangJen Chiu, Senior Member, IEEE AbstractThis study proposes an isolated LLC resonant converter with MHzlevel switching frequency that can achieve zero voltage switching in the full load range. In the proposed converter, conventional silicon devices are replaced with wide bandgap GaN devices to reduce switching losses in the power device. A planar transformer structure with reduced winding length on the secondary side is proposed that utilizes flux cancellation and reduces core loss while maintaining a low core volume. The path of the secondary winding is a fraction of a full turn, which reduces secondaryside losses while maintaining a turns ratio of 16:1. This planar transformer achieves the goals of decreasing core loss and volume, while increasing power density. Within a limited circuit layout area, optimal points for the efficiency of core loss and copper loss were calculated. The magnetic simulation software ANSYS Maxwell was employed to verify whether the actual circuit behavior of this planar transformer conformed to the design theory. Finally, a resonant converter was achieved with a switching frequency operating at 1 MHz, input voltage of 380 V, output voltage of 12 V, output power of 800 W, power density of 55 W/cm 3, and maximum efficiency of 96.5%. I. INTODUCTION With the development related to the global race into the Industry 4.0 era, demands for energy are increasing. The technological evolution of the Internet of Things, big data analysis, artificial intelligence, and cloud computing has led researchers to turn their attention to energy conservation. In 2014, according to reported data, energy consumed by computer, communication, and server power sources accounted for 1.8% of the United States total electricity consumption. Furthermore, electricity consumption is increasing annually, with the total in the United States estimated to reach 73 billion kw by 2020 [1]. Therefore, energy waste can be considerably reduced if the conversion efficiency of power supplies can be effectively enhanced. At the same time, various industries are demanding power supplies with smaller volume at the same power rating. Following the rapid development of equipment for datacenters and cloud servers, numerous types of highefficiency DCDC converters have been widely employed, such as the phaseshift full bridge converter [25] and LLC resonant converter [68]. The phaseshift full bridge converter can achieve zero voltage switching (ZVS) of the primary side switch [911] through the energy stored by the leakage inductance of the transformer. However, its ZVS condition is related to the output load, and the switching loss of the power switch cannot be reduced at a light load. When the switching frequency reaches the MHz level, switching loss remains high even with the use of wide bandgap devices. Therefore, for the pursuit of high power density and high conversion efficiency, applying phaseshift full bridge converters to highfrequency operations at the MHz level is not suitable. By contrast, when the switch operating frequency of an LLC series resonant converter is between the first and second resonant frequencies, the ZVS conditions of its power switch are unrelated to load; furthermore, it is characterized by the ZVS of the primary side switch and the zero current switching (ZCS) of the secondary side rectifier switch [1213]. This approach can substantially reduce switching loss and electromagnetic interference [1416] of the converter at high frequencies. To achieve high power density and high efficiency of the converter, the volume of the magnetic component can be decreased through increasing the switching frequency. However, the switching loss of the power switch as well as the core and copper losses of the converter also increase as the frequency increases. The power device and magnetic component must be optimized to solve these difficulties. Although LLC resonant converters possess ZVS to reduce highfrequency switching losses, they nonetheless exhibit exceedingly high turnoff losses when using conventional silicon devices. The use of a wide bandgap device gallium nitride (GaN) [1719] to replace conventional silicon devices is an effective method for reducing turnoff losses. Because GaN devices have a smaller parasitic capacitor, their switching speed is substantially higher than that of conventional silicon devices, making them more suitable for switching at the MHz level. The ZVS characteristic of LLC resonant converters and the use of wide bandgap devices can effectively reduce the switching loss of a power device at MHz switching frequencies. Therefore, the design of the magnetic component is the primary challenge for highfrequency LLC resonant converters in terms of efficiency and power density. The primary transformer losses for LLC resonant converters are core loss and copper loss. Core loss of a highfrequency core can be further examined from two perspectives: the material selection, and the flux cancellation method. The former can be obtained according to user manuals provided by core material suppliers, such as Ferroxcube, TDK, and ACME. If a core material of khz is used at a switching frequency of 1 MHz, its core loss will increase more than several tens of times. Therefore, according to previous studies [20, 21], core materials that are suitable for use at different frequencies can be obtained.
2 This approach is based on the perspective of core materials, and the further reduction of core losses following the selection of an appropriate core material presents another challenge. In the literature, several methods for reducing core loss through flux cancellation have been proposed. These methods can be further divided into using numerous vertically stacked cores to enable flux cancellation in the stack [22], and moving the winding position from the center leg on the EI core to the outer leg and having the winding rewound in the opposite direction for flux cancellation to be achieved on the center leg [23, 24]. Although both methods can effectively reduce core losses, the former method entails stacking the core which decreases the power density of the converter. Thus, the latter method is more suitable for achieving increased power density. In addition, the transformer copper loss of LLC resonant converters can be examined from the perspectives of power density and loss. Conventional transformers are generally wound using litz wires. By comparison, a printed circuit board (PCB) layout has an advantage over a conventional transformer in that it requires a smaller window area than conventional transformer for the winding wire [25, 26]. To achieve high power density, the present study employed a PCB layout to replace conventional litz wire winding for the transformers. Another method for reducing copper losses involves using circuit architecture and transformer winding. egarding the application specification of cloud servers, when the secondary side output is employed for high current applications, a centertap rectifier structure is employed instead of a full bridge rectifier structure. In a centertap rectifier structure, a parallel secondary side synchronous rectifier switch is employed to reduce the conduction loss of the transformer s secondary side as well as that of the synchronous rectifier switch. However, this approach cannot reduce the copper loss on the secondary side of the transformer. Therefore, studies have proposed the concept of a matrix transformer circuit architecture [27, 28]. The matrix transformer splits the main transformer into several transformers and employs a circuit architecture in which the primary side winding is connected in series and the secondary side winding is connected in parallel. This method can effectively reduce the current in each secondary winding, thus reducing copper loss. Several methods based on the secondary parallel architecture of the matrix transformer circuit exist for reducing the dc resistance of a transformer winding. Because the selection of different effective core crosssectional area shapes affects the circumference of each turn on the winding, changes in the shape of this area of the transformer [25, 29] can effectively reduce some winding loss. Another approach is to change the winding method of the transformer, an example being splitflux transformers [3034]. This design changes the restriction of conventional transformer winding, which requires a full turn, as well as takes advantage of the matrix transformer architecture. This also causes the simultaneous conduction of several secondary sides, forming several fractionalturns on the transformer. For the transformer, however, these in fact constitute one full turn. Such an approach can effectively and substantially reduce the copper loss of a transformer. However, in terms of actual transformer design, Faraday s law dictates that when the number of windings is decreased, the effective crosssectional area of the core must be increased by the same multiple as the number of winding turns decreased to maintain the same peak flux density. Then, the overall core volume increases as the effective crosssectional area increases. For example, the core volume in a halfflux (or halfturn) transformer [32, 33] increases twofold, and the core volume in a quarterflux (or quarterturn) transformer [34] increases fourfold. In this paper, several transformer core structures are discussed. In addition to the integration of the flux cancellation method to reduce core loss, a novel planar winding structure with a fractional turn length on the secondary side is proposed to solve the disadvantages of core losses and volume increase that accompanies a splitflux transformer. An LLC resonant converter was employed in this study, and the switching frequency was operated at the resonant frequency as a dc transformer to achieve the highest conversion efficiency [35, 36]. There is no specific requirement for leakage inductance in this design to regulate the output voltage. If a designer needs a specific leakage inductance to operate over a wide input voltage range or adjusting voltage gain to regulate the output voltage, work in [26, 29] provide information to address leakage inductance. For the proposed converter, a wide bandgap device GaN was employed to reduce the switching loss of highfrequency application. In the proposed transformer, the primary winding used flux cancellation concepts for the windings to decrease core loss. PCB windings were used to achieve a highfrequency planar transformer, and interleaving was used for the winding arrangement to reduce the magnetomotive force (MMF), thereby decreasing the ac resistance loss [23, 24]. Ultimately, the proposed planar transformer structure can achieve 16 turns on the primary winding with less than a full turn s length on the secondary winding. However, the turns ratio of the transformer exhibits an effect of 16:1. This structure reduces the dc resistance loss of the secondary side and decrease core volume to increase power density. Parametric equations were employed for the design of the transformer dimensions. Using the limited usable area of the circuit board, optimal parameters were found for core loss and copper loss, and the magnetic simulation software ANSYS Maxwell was used to confirm the flux balance of the proposed transformer as well as whether its functions conformed to the design concept of the transformer. The contribution of this work is the design and analysis of a unique transformer structure that combines the advantages of the matrix transformer UI core and the reduced winding length of splitflux transformers to reduce transformer volume while minimizing losses. In the experiment, the final LLC resonant converter achieved an operating frequency of 1 MHz, input voltage of 380 V, output voltage of 12 V, output power of 800 W, maximum efficiency of 96.5%, and power density of 55 W/cm 3. II. ANALYSIS OF FLUX INDUCED ON THE SECONDAY SIDE OF THE TANSFOME
3 This section examines differences in the induced flux of the secondary side winding of a splitflux transformer when different core structures are adopted, which result in differing induced voltages on the secondary side. Previous studies proposed a halfflux transformer with an EI core structure [3233], as shown in Fig. 1. Assume that the primary winding is wound counterclockwise on the center leg. The secondary winding may be wound in the form of an equivalent full or halfturn, as shown by the orange line and green line in Fig. 1, respectively. Faraday s Law of electromagnetic induction is shown in (1), where v is the induced voltage, n is the number of turns, and ϕ is the magnetic flux passing through the circuit. The magnitude of the secondary induced voltage is related to the turns ratio of the transformer and the magnetic flux generated on the primary side. To simplify the following analysis, it is assumed that windings on the primary side of the transformer are all one turn, and the magnetic flux generated on the primary side is 1ϕ. Fig. 1 shows that the magnetic flux generated by the primary winding on the center leg is 1ϕ, where the crosssectional area of the outer leg of the conventional EI core is onehalf of the center leg. According to the theory of magnetic resistance, the magnetic flux flowing into the outer leg is 0.5ϕ. The closedloop magnetic circuit passes through by the secondary winding of the transformer, and although the green line only passes through a 0.5ϕ closedloop magnetic circuit, the orange line passes through two 0.5ϕ closedloop magnetic circuits. The orange line represents a conventional transformer that employs a secondary winding structure with full turns; its induced voltage is the same as the primary side winding. The green line represents the halfflux transformer structure proposed in [3233]. Because the flux of the closedloop magnetic circuit through which the secondary winding passes is only 0.5ϕ, the induced voltage is half of the voltage on the primary side. d v= n (1) dt Fig. 1. Induced flux of a halfflux transformer: side view and top view. Next, the application principle of a quarterflux transformer proposed in [34] is discussed, which is shown in Fig. 2. When the primary winding is wound counterclockwise around the center leg, the flux generated is 1ϕ. In the core structure, the sum of the crosssectional areas of the four outer legs is equal to the crosssectional area of the center leg. According to the theory of magnetic resistance, the flux flowing into each outer leg is ϕ. In the closedloop magnetic circuit formed by the secondary winding of the transformer, the green, purple, orange, and blue lines pass through closedloop magnetic circuits of ϕ to four times ϕ, respectively. Therefore, the induced voltages of these four lines are times the primary side voltage to one time the primary voltage, respectively Fig. 2. Induced flux of the quarterturn transformer: side view and top view. The proposed design integrates the design methods suggested in [3034] to achieve a splitwinding planar transformer. Because the number of turns on the secondary winding were no longer a full turn, the number of primary turns was decreased to maintain the same output voltage as that of the fullturn transformer. For example, with the specifications of a 380V input and 12V output, the primary and secondary turns ratio of the transformer is usually 16:1. For a halfflux transformer, however, this ratio becomes 8:0.5, whereas for a quarterflux transformer it would be 4:. Although the splitflux transformer can reduce copper losses of the primary and secondary sides, at a fixed peak flux density, the effective crosssectional area of the core must increase proportionally to counteract the increase in peak flux density caused by a decrease in the number of primary turns. For example, the core effective crosssectional areas of the halfflux transformer and quarterflux transformer must increase by two and four times, respectively, compared with the fullflux transformer to achieve the same peak flux density. This not only increases the core volume, but also decreases the power density of the converter. To overcome the core volume and loss increases caused by a splitflux transformer, this paper proposes a method of applying a core structure that achieves flux cancellation with a UI core with fractional turns on the secondary side to reduce winding length, as shown in Fig. 3. The primary windings are wound clockwise around the left leg and counterclockwise around the right leg, generating a flux of 1ϕ. Therefore, the core structure used at this time only has two legs, which differs from conventional splitflux core; the flux flowing through the two cylinders are both 1ϕ. Therefore, although the orange line and green line pass through one turn and a halfturn respectively, the induced flux of the secondary side remains 1ϕ. This means that when the transformer employs the winding method of the green line, the induced flux of the secondary winding is 1ϕ as long as the winding passes through the transformer window, even if the winding length is less than a full turn. Thus, even when the input voltage is 380 V and output voltage is 12 V, the `
4 turns ratio can be maintained at 16:1. The same peak flux density can be maintained without needing to increase the core s effective crosssectional area. In the proposed core structure, the induced magnetic flux on the secondary side is not affected by the winding method or the length of the winding. The induced magnetic flux on the secondary side is only related to the primary magnetic flux and the number of passes through the closed magnetic loop (window of the core). This work has the same induced magnetic flux on the secondary side of the transformer as that of the traditional winding with a full winding. Thus, the secondary side winding achieves a fractional winding structure at the same maximum magnetic field strength B max as the traditional transformer, but increased core volume associated with previous splitflux transformer designs can be avoided. Table 1 compares the aspects of different highfrequency transformer winding methods. The proposed UI planar transformer with fractional turns to reduce the secondary winding length has approximately half the secondary copper loss compared with a matrix transformer and half the core volume and loss compared with a halfflux transformer. Furthermore, compared with a quarterflux transformer, although the primary and secondary winding losses of the proposed transformer are four and two times, respectively, its core volume and loss are times, still giving it a substantial advantage for achieving the goals of high power density and high efficiency. S 1 and S 2 are the primary power devices using GaN components; L r and C r are the resonant inductor and resonant capacitor, respectively; L m is the magnetizing inductor of the transformer; and Sa and Sb are the positive and negative halfcycle rectifier switches for the secondary side, respectively. The number of turns on the primary side of the transformer is 16, and there are 0.5 turns for each secondary center tap, thus achieving a 380V input and 12V output. The primary and secondary windings of the transformer are wound on the two outer legs of the core, with 16 turns for the primary winding, as shown in Fig. 5. There are 0.5 turns for the secondary winding, as shown in Fig. 5. Vin S1 S2 Cr Lr 16 : 1 : 1 : 1 : 1 : 1 : 1 : 1 : 1 Lm Sb1 Sa1 Sb2 Sa2 Sb3 Sa3 Sb4 Sa4 Fig. 4. Circuit diagram of the proposed transformer and LLC converter Fig. 3. Schematic of the induced flux of the halfflux transformer: side view; top view Vin S1 S2 Table 1: Comparison of Different Transformer Structures Transformer Structure Matrix [24] Halfflux [3233] Quarterflux [34] UI with fractional turns Frequency 1 MHz 1 MHz 1 MHz 1MHz Turns ratio 16:1 8:0.5 4: 16:1 Primary turns Secondary turns (length) Ae Ae 2 Ae 4 Ae Ae Volume Vel 2 Vel 4 Vel Vel III. OPEATING INTEVAL OF THE POPOSED TANSFOME This section discusses the operation of the LLC converter with 0.5 turns on the secondary side. Fig. 4 is the circuit diagram, where V in is the input voltage; V out is the output voltage; Sa1 Sb3 Sa2 Sb2 Fig. 5. Schematic of transformer winding: primary side winding and secondary side winding During the positive half cycle, the primary upper switch S 1 is on and the lower switch S 2 is off. As shown in Fig. 6, the current direction of the primary side is counterclockwise for the left leg and clockwise for the right leg, causing an induced magnetic field inside the core. The direction of the magnetic field is Sa4 Sb4 Sa3 Sb1
5 depicted in Fig. 7. According to Faraday s law, the secondary side of the transformer generates a clockwise current in the left leg, whereas a counterclockwise current is generated in the right leg against the applied magnetic field. The secondary side current of the transformer flows from the ground (GND) to Sa 1, Sa 2, Sa 3, and Sa 4, then flows through the secondary winding, and finally flows out toward the V out point. As shown in Fig. 7, any point V out is connected to the same point as the remaining three points, and any point GND is connected to the same point as the remaining GND points. Therefore, the secondary winding can be viewed as a parallel relationship, and the equivalent number of secondary turns is 0.5. Four sets of secondary side joints are separately wound around the left and right legs of the core, and the secondary winding of each leg passes through the core window, seeing the full flux of the core. The generated magnetic field is similar to that of a conventional center leg wound for a full turn. Thus, the magnetic field in the transformer does not develop an imbalance. V in S 1 C r Sb 1 Sa 1 Sb 2 primary current direction comprises a clockwise direction for the left leg and counterclockwise direction for the right leg, which generate an induced magnetic field inside the core. The magnetic field direction is shown in Fig. 9. According to Faraday s law, the secondary side of the transformer generates a current in the counterclockwise direction on the left leg, and a clockwise current on the right leg against the applied magnetic field. The secondary current of the transformer flows from GND to Sb 1, Sb 2, Sb 3, and Sb 4, then flows through the secondary winding, and finally flows out toward point V out. Any point V out is connected to the same point as the remaining three points, and any point GND is connected to the same point as the remaining GND points, as shown in Fig. 9. When any switch is turned on and current flows in the transformer, the secondary winding of the transformer sees the full flux induced through the core. Therefore, this method is equivalent to conventional transformer winding in terms of magnetic flux and does not possess the disadvantages of core volume and loss increases that other splitflux transformers do. Compared with transformers with conventional winding methods, this method effectively reduces copper losses on the secondary winding of the transformer under large output currents. Sb1 S 2 L m Sa 2 Sb 3 V out S1 Cr Sa1 Sb2 Vin L r Sa 3 Sb 4 S2 Lr Lm Sa2 Sb3 Sa3 Sb4 Sa 4 Fig. 6. Current path of the positive half cycle Fig. 8. Current path of the negative half cycle Sa4 S1 S1 Vin Vin S2 S2 Sa2 Sa4 Sa2 Sa4 Sa1 Sa3 Sa1 Sa3 Sb3 Sb1 Sb3 Sb1 Sb2 Sb4 Sb2 Sb4 Fig. 7. Current path of the positive halfcycle winding: primary side and secondary side During the negative half cycle, the primary upper switch S 1 is off and the lower switch S 2 is on. As shown in Fig. 8, the Fig. 9. Current path of the negative halfcycle winding: primary side; secondary side IV. STUCTUAL ANALYSIS AND DESIGN OF THE PLANA TANSFOME COE
6 This section introduces the core structure and design of the proposed planar transformer. Using a parametric design under a limited area for circuit layout, the optimal design parameters to reduce core loss were determined. A placement with minimal ac resistance loss was found, which is particularly challenging to minimize at high switching frequencies in the MHz range. ANSYS Maxwell was employed to analyze the secondaryside winding length of the proposed transformer, as well as to ensure that positive and negative halfcycle imbalance would not occur in each centertap current of the secondary side. To achieve the highest efficiency of the LLC resonant converter, the operating frequency was fixed at the resonant frequency and the LLC resonant converter was used as a dc transformer. The circuit specifications in this study were as follows: an input voltage of 380 V, output voltage of 12 V, and output wattage of 800 W. The core structure was parameterized to examine the relationship between core loss and copper loss and to select the appropriate core dimensions, as shown in Fig. 10, where r is the effective crosssectional area radius of the core, is the maximum length of the winding radius, T is the thickness of sheet I, and Z is the cylinder height. 2 r 4 2 ( )= r Because the flux density must be consistent in each path to avoid complications with magnetic field lines and hotspot concentration, the core leg effective crosssectional area must be equal to the crosssectional area of the magnetic flux flowing through sheet I. The conventional UI core structure is shown in Fig. 11, and the thickness of sheet I at this time is calculated by (4). To reduce the overall height of the transformer, the top and bottom covers of the transformer were optimized. Fig. 11 illustrates that when the core structure of the transformer is the same as that of the conventional UI core, the area occupied by the circuit layout of the transformer and the area of the transformer winding to obtain the occupancy area of the entire transformer must be considered. The total area of the transformer at this time was 8 2. Therefore, using the same total area, this paper proposed increasing the magnetic circuit of the transformer outward while maintaining the same effective crosssectional area. Simultaneously, the thicknesses of the top and bottom covers of the transformer were decreased. The core shape after the volume increase is shown in Fig. 11. The thickness of sheet I can be rewritten as (5); because α is the ratio of the winding radius and core radius, and because the winding radius must be greater than the core radius, α must be greater than 1. Additionally, this means that the thickness of the I sheet in Fig. 11 is smaller than that in Fig. 11. The total volume of the core can be expressed using (6). 4 (3) T T Fig. 10. Graph of core dimensions In consideration of the loss characteristics of highfrequency materials, the peak flux density should not exceed 100 mt. The usage manual of magnetic materials reveals that when the peak flux density of a ferrite core exceeds 100 mt, core loss increases sharply. Therefore, this work selected a unit volume loss of 600 kw/m 3 to execute the following design. Hitachi s highfrequency magnetic material ML91S was used as the ferrite core material. When the core loss per unit volume was 600 kw/m 3 and the switching frequency was 1 MHz, the peak flux density was found to be 74 mt. (2) was used to obtain the effective crosssectional area of the core at this time, A e, at mm 2, and the radius r at 3.56 mm. In (2), V in is the input voltage of the circuit, at 380 V; B m is the peak flux density with a value of 74 mt; N p is the number of turns in the primary winding, 16 turns; and f sw is the operating frequency of the circuit, at 1 MHz. 2 Vin Ae = r = (2) 8 B N f Next, using the parametric equation α of the core, as shown in (3); the larger the value of α, the larger the core winding radius. The value of the winding radius subtracting the core effective crosssectional area radius r is the winding width of the core. A greater width results in smaller dc resistance of the transformer winding as well as smaller copper loss. max p sw Z 2 2 r r 4 Copper Copper Fig. 11. Diagram of core dimensions: original core; optimized core r T = (4) 2 r T ( )= 2 2+2r Core ( ) ( ) ( ) Vel = Ae z + T + T Using the Modified Steinmetz Equation, core loss can be expressed using parameters as shown in (7), where P v is the core loss per unit volume, and its value forms an exponential ratio with the values of the operating frequency and peak flux, as shown in (8). Among these, C m, x, and y can be obtained from the core materials manual of the manufacturer. Finally, different volume sizes can be obtained according to differences 2 2r 4 Core (5) (6)
7 in the core proportional parameter α, thereby obtaining core loss. As the α value and core volume increase, assuming a fixed P v, core loss also increases accordingly. Coreloss ( ) Pv Vel ( ) = (7) x 1 y ( max ) P = C f B f (8) v m eq sw Next, ANSYS Maxwell was employed to verify differences between before and after the thickness optimization of the core I sheet. Fig. 12 shows that although the peak flux density in this study was designed to be 74 mt, magnetic flux was not evenly distributed on the magnetic circuit of the core. Therefore, using Maxwell, this work observed that the highest flux density at this time was approximately 114 mt. In Fig. 12, additional volume of the core is added with a peak flux density of approximately 74 mt, which is exceedingly close to the original design value. Using the magnetic material core loss parameter, it was found that when the core peak flux density exceeded 100 mt, core loss increased sharply. In Fig. 12, when α was 2.45, the core loss was 9 W, and in Fig. 12 after the thickness optimization of sheet I it was 3.7 W. This optimization method decreases the core height under condition of the same occupancy area as well as effectively mitigates the increase in core loss caused by the uneven distribution of peak flux density. substantially. The total ac resistance is obtained by summing (9) and (10), as shown in (11). ( ) + sin ( ) ( ) ( ) sinh = 2 cosh cos ac _ skin dc ( ) sin ( ) ( ) + ( ) sinh ( 2m 1) 2 cosh cos 2 ac _ = proximity dc ac _ total ac _ skin ac _ proximity (9) (10 ) = + (11) Finally, based on the previous calculations of core loss and ac copper loss, the total transformer loss can be obtained by summing these values, as shown in Fig. 13. The figure reveals that a minimum loss point appears when α is 2.45; this α value was ultimately employed as the final design parameter. A design diagram with core dimensions is shown in Fig. 14, where is the top view of the core and is the side view of the core. 25 Loss (W) Total Loss Core Loss Copper Loss Fig. 12. Maxwell simulation diagram: original core; optimized core Next, this section examines copper loss. First, the dc resistance of the transformer winding can be expressed using (9), where the winding length is represented by Length, ρ is the resistivity of the copper wire, h is the winding thickness, and Width is the width of the copper wire. Length( ) copper ( ) = (9) h Width ( ) Considerations of the thickness of the winding wire require observations of the effect of ac resistance. Based on the assumptions of Dowell s equation [37], under the condition of a sinusoidal current at the excitation source for copper foil, the influence of the skin effect on ac resistance can be expressed using (9). The influence of the proximity effect on ac resistance is expressed using (10). For the application of multilayer winding, the influence of the proximity effect substantially exceeds that of the skin effect, and its influence can be expressed by the size of m, where m represents the MMF corresponding to each layer. The minimum MMF can be achieved when a full interleaving winding method is used; thus, the influence of m can be minimized. However, if a nonfullinterleaving winding method is used, the ac resistance corresponding to windings with larger MMF increases r=3.568 mm Fig. 13. elationship between α value and total loss mm mm =8.742 mm =8.742 mm mm r=3.568 mm Fig. 14. Actual core size: core top view; core side view ANSYS Maxwell was used to analyze and verify this concept and whether it could be applied to the winding structure of the transformer, as well as to verify whether the turns ratio of the secondary side conformed to the analysis in the previous section. To obtain accurate simulation results, a 1:1 3D model of the core was constructed. The method employed in ANSYS Maxwell used the external circuit function, where a capacitor and inductor were connected in series as the resonant tank to the primary side of the transformer, and waveforms were used to generate square wave voltage, crossing the two ends of the capacitor and the inductor and transformer, thereby simulating 7.5 mm T=2.25 mm Z=3 mm Z=3 mm T=2.25 mm
8 the exact working condition of the LLC resonant converter. Table 2 presents the simulation parameters. For the proposed transformer, Figs. 15 and 16 reveal that even when the actual winding length of the secondary side is approximately half a turn, the primary to secondary voltage ratio of the transformer remains 16:1. Fig. 17 verifies that regardless of when the transformer is conducting in the positive half cycle or negative half cycle, the core achieves balanced magnetic flux. respectively. Fig. 18(c) is the actual core. Fig. 18(d) and Fig. 18(e) are the circuit layout and current directions, respectively, of the secondary side. The height of the overall circuit was 0.7 cm and the power density of the LLC converter was 55 W/cm 3. Table 2: Maxwell Simulation Parameters Specification Items Transformer material esonant capacitor esonant inductor Transformer voltage source Magnetizing inductor esonant frequency Circuit Parameters ML91S 32 nf 768 nh ±190 V 25 uh 1 MHz 6.5cm 3.2cm Fig. 15. The transformer s primary voltage stress (c) S S Vo Fig. 16. The transformer s secondary voltage stress Fig. 17. Balanced flux distribution V. EXPEIMENTAL VEIFICATION This section details the experimental verification of an LLC resonant converter with the proposed UI planar transformer with input voltage of 380 V, output voltage of 12 V, output power density of 800 W, and operating frequency of 1 MHz. Components in the 3D model and the dimensions of the transformer are presented in Fig. 18 and Fig. 18, Vo (d) (e) Fig D model: component labels, actual circuit and (c) actual core, (d) current directions of the secondary side during the positive half cycle, and (e) current directions of the secondary side during the negative half cycle Table 3: Measured LLC Converter Circuit Specifications Specification items Input voltage V in Output voltage V out Output maximum power P o esonant frequency f r Circuit operating frequency f sw Specification data 380 V 12 V 800 W 15 MHz 1 MHz Table 3 presents the circuit specifications in this study. The circuit parameters for the LLC resonant converter, switching components, and magnetic materials are shown in Table 4. The measured waveforms of the circuit are shown in Fig. 19, where the output load is 100%, with I o = 66.7 A. The measured S S
9 waveforms were the resonant tank current of the primary side and the waveform of the primary lower bridge V ds. Table 4: Circuit Usageelated Parameters Specification Transformer turns ratio Core material Primary power switch Secondary synchronous rectifier component Primary isolated driver IC Secondary isolated driver IC esonant capacitor esonant inductor Magnetizing inductor Component/Parameter 16:1, 0.5 turn length on secondary side ML91S GS66508T BSC0500NSI SI8271LS FAN nf 768 nh 21 μh Loss (W) Transformer Core Loss Copper Loss(ac) Copper Loss(dc) Conduction Loss Switching Loss BSC0500NSI GS66508T Fig. 21. Loss analysis of the full load Other Fig. 19. Primaryside V gs, V ds, and resonant current The measured efficiency curve of the circuit is shown in Fig. 20, where the highest efficiency is 96.5% when the output power is 400 W. The loss analysis of the full load is shown in Fig. 21. According to the loss analysis, the total transformer loss was approximately 13 W, which included core loss and dc and ac copper losses. The switching loss on the primary side was approximately 12 W, which included the turnoff switching loss and conduction loss. Because the secondary power switch possessed the characteristics of ZCS, switch loss comprised only the conduction loss, for a total of 13.6 W. Other losses include circuit winding loss, terminal loss, and input and output capacitor losses. Efficiency (%) Output Power (W) Fig. 20. Experimental efficiency curve of the circuit Fig. 22 presents a power density comparison of various 380 V to 12 V dcdc converters, where [20, 2324] use matrix transformers and operate at 1MHz switching frequency with transformers that employ flux cancellation to reduce core losses. The proposed planar UI transformer s structure has lower copper loss than the traditional UI matrix transformer. By utilizing the induction of the transformer flux, the proposed transformer also has flux cancellation, such that it achieves lower core loss and copper loss than the traditional UI matrix transformer. In the LLC converter matrix transformer developed in [24], several transformers were integrated together to achieve an overall power density of 54 W/cm 3. The LLC converter with the proposed converter achieves a power density that is 1 W/cm 3 higher than [24], but the overall conversion efficiency of this work is 1% lower. Compared to [24], the proposed transformer does not achieve full flux cancellation to reduce the eddy current loss in winding, but the major advantage is the fractional turn winding on the secondary side that reduces the length of the winding and associated losses. Although the results have not shown an advantage in overall converter efficiency, but based on the core structure alone, losses in the transformer for the proposed structure are lower than that of the matrix transformer structure in [24]. A detailed comparison of the different types of losses in each structure are provided in the Appendix. In [3034], a splitflux transformer architecture was presented in which fractional turns were used to reduce secondary copper loss. The transformer structures adopted by [30] and [32] are traditional halfflux transformers. Both use an EI core and the secondary winding forms an equivalent halfturn. For the secondary winding method of the transformer in [30] and [32], the difference between the two is only in the rectification structure of the secondary side. In [32], the halfflux transformer structure used has an input voltage of 380 V and an output voltage of 12 V. Therefore, a centertap structure is adopted at the rectifier side, and the fractionalturn structure effectively reduces copper loss. The quarterturn transformer in [34] uses a single core with multiple sets of center taps in parallel, and the secondary winding of the transformer uses
10 fractional turns to further reduce copper loss. To reduce the number of primary side primaryside turns to a quarter of the original and maintain the same B max, the crosssectional area A e would need to increase four times, such that the overall volume would also increase four times. For the goal of high power density, the increased core volume associate with previous splitflux transformer designs is a challenge that the proposed design overcomes. Note that the proposed planar transformer design is appropriate for higher input voltage and high stepdown ratio applications, like 380 V input to 12 V output, but loses some of its advantages for lower voltage, higher current converter applications. In the present study, the concepts of flux cancellation and fractional turns were combined and flux induction was used to achieve a turns ratio of 16:1, even though the secondary winding length is less than a full turn. The disadvantage of the need for an exponential increase in core volume for a splitflux transformer was solved, ultimately reaching a power density of 55 W/cm 3. The proposed transformer structure could also be applied to other high stepdown converters with multiple windings on one side to achieve high power density. A comparison of this paper and similar transformer structures is shown in Table 5. Work in [23] and [24] adopt only the traditional matrix transformer structure, while [30, 32, 34] use a splitflux transformer structure. In [23] and [24], the secondary winding structure is a full winding; in [30, 32] and this paper, the secondary winding length is equivalent to a halfturn; in [34], the secondary winding is equivalent to a quarterturn. It follows that the copper loss on the secondary side, in [32, 34] and this paper, are lower than in [23, 24]. For a more detailed comparative analysis of the various splitflux transformers and the proposed structure, see the Appendix. Table 5: Comparison of Similar Matrix Transformer Attributes Fig. 22. Power density comparison table VI. CONCLUSION In this paper, a planar transformer with fractional turns on the secondary side was proposed for a high power density LLC resonant converter. Using the resonant characteristics of this converter and GaN switches, conduction and turnoff losses at a switching frequency of 1 MHz were greatly reduced. For the planar transformer design, flux cancellation was employed to target core losses by placing the primary winding on the outer leg and utilizing reverse windings to reduce core losses. The secondary side of the transformer employed equivalent halfturn winding length to reduce the dc resistance loss while maintaining a 16:1 turns ratio. As a result, power density could be increased and core volume decreased at the same peak flux density. Furthermore, using the core parameter α, an optimized core size was designed with considerations of core loss, copper loss, and power density within a limited circuit layout area. ANSYS Maxwell was employed to verify that the structure of the secondary windings conformed with the theoretical analysis. Finally, the proposed planar transformer for an LLC resonant converter was achieved with an output power of 800 W, switching frequency of 1 MHz, maximum efficiency of 96.5%, and power density of 55 W/cm 3. [23] [24] [30] [32] [34] This work Vin/Vo 390V/ 12V 380V/ 12V 120V380V/5V 20V 380V/ 12V 380V/ 12V 380V/ 12V Output power 1 kw 800 W 36 W 600 W 1 kw 800 W Operating frequency 1 MHz 1 MHz 0.5 MHz1.3MHz 750 khz 1 MHz 1 MHz UI with Transformer structure Matrix SplitFlux fractional turns Turns of primary winding Turns of secondary winding (length) Core shape UI 4 leg EI EI 5 leg UI Power density 51 W/cm 3 54 W/cm 3 Not mentioned 21.3 W/cm 3 38 W/cm 3 55 W/cm 3 Peak efficiency 95.4 % 97.6 % *91 % 98 % 97 % 96.5 % Power Density (W/cm 3 ) [27] 1.6MHz 94.5%, 50 W/cm 3 This paper 1MHz 96.5%, 55 W/cm 3 [23] 1MHz 95.5%, 51 W/cm 3 [20] 1MHz 97%, 42 W/cm 3 [34] 1MHz 97%, 38 W/cm 3 [33] 500kHz 97%, 23.1 W/cm 3 [32] 750kHz 98%, 21.3 W/cm 3 [13] 1MHz 95.5%, 12.2 W/cm 3 [24] 1MHz 97.6%, 54 W/cm Peak Efficiency (%) [26] 700kHz 97%, 10.4 W/cm 3 99
11 APPENDIX. This appendix compares the design differences between the traditional matrix transformer structure, different splitflux transformer structures, and this work. The input voltage is 380 V, the output voltage is 12 V, the output power is 800 W, the switching frequency is 1 MHz, the primary side topology is a halfbridge structure, and the secondary side consists of four sets of center taps connected in parallel. That is, 16 primary turns, and 1 secondary turn for the traditional transformer; 8 primary turns and 0.5 secondary turns for the halfflux transformer; and 4 primary turns and secondary turns for the quarterflux transformer. The number of primary turns of the transformer proposed in this paper is 16 turns, and the length of the secondary side winding is equivalent to 0.5 turns. Next, the maximum magnetic field strength B max from Faraday s Law (12) is set to 76 mt and PUI22 is selected as the singleloop transformer core. Because the primary winding of the halfflux transformer is 8 turns, according to Faraday's Law, the crosssectional area A e should be doubled. Therefore, if the core PEI22 is used, the volume of the quarterturn transformer would increase fourfold, which is equivalent to four PUI22. Next, the core loss is calculated. Since the B max of the transformer is the same, the core loss is proportional to the volume according to the Modified Steinmetz Equation (13). The results, summarized in Table 6, show that the volume and core loss of a quarterturn transformer is four times that of a fullturn matrix transformer. Vin Bmax = (12) 8 Np fsw Ae x 1 y ( max ) P = C f B f (13) v m eq sw Then, the copper loss of the transformer is calculated. The MS value of the primary current is 2.5 A and the MS value of the secondary current is 16.5 A. The winding width of the PUI22 core is 4 mm. The calculation is for a circle, where the thickness of each winding is that of 2 oz copper in a PCB layer. Since the effective current values are the same, the copper loss of the transformer winding is only related to the length of the winding. The winding arrangement and ac resistance ac calculation are not considered here because the it is highly dependent on the exact winding arrangement that depends on the specific application. The loss of the winding can be obtained as shown in Table 6. The transformer structure proposed in this paper has the same primary winding method as the matrix transformer but the secondary winding method is equivalent to the halfflux transformer. Therefore, primary copper losses are the same as the matrix transformer, while the secondary copper losses are the same as the halfflux transformer. Summing the transformer core loss and copper loss in Table 6, the proposed transformer has the best performance in terms of core volume and transformer loss. Table 6: Comparison of Similar Transformer Attributes Transformer structure Vin/Vo Output power Operating frequency Primary side topology Secondary side topology Transformer voltage ratio Primary side turns Bmax FullTurn Matrix Halfflux 380V/ 12V 800W 1 MHz Half bridge topology Quarterflux 4 Centertap topology 16:1 This work mt Core size PUI22 PEI22 PUI22*4 PUI 22 Ae (mm 2 ) Vol. (mm 3 ) Material ML91S Core loss (W) Primary side MS 2.5 A current Secondary side MS 16.5 A current Winding width 4 mm Copper thickness 2 oz Primary copper loss (W) Secondary copper loss (W) Total loss (W) EFEENCES [1] E. Orlando, Lawrence Berkeley National Laboratory, United States data center energy usage report, Jun [2] K. Shi, D. Zhang, Z. Zhou, M. Zhang and Y. Gu, "A Novel PhaseShift Dual FullBridge Converter With Full SoftSwitching ange and Wide Conversion ange," in IEEE, vol. 31, no. 11, pp , Nov [3] J. Kim, D. Kim, C. Kim and G. Moon, "A Simple Switching Control Technique for Improving Light Load Efficiency in a PhaseShifted Full Bridge Converter with a Server Power System," in IEEE Transactions on Power Electronics, vol. 29, no. 4, pp , April [4] Y. Liu et al., "Integrated magnetics design for a fullbridge phaseshifted converter," 2018 IEEE Applied Power Electronics Conference and Exposition (APEC), San Antonio, TX, 2018, pp [5] B. Chen and Y. Lai, "Switching Control Technique of PhaseShift Controlled FullBridge Converter to Improve Efficiency Under Light Load and Standby Conditions Without Additional Auxiliary
12 Components," in IEEE, vol. 25, no. 4, pp , April [6] H. Wu, T. Mu, X. Gao and Y. Xing, "A SecondarySide PhaseShift Controlled LLC esonant Converter With educed Conduction Loss at Normal Operation for HoldUp Time Compensation Application," in IEEE, vol. 30, no. 10, pp , Oct [7] J. Lee, J. Kim, J. Kim, J. Baek and G. Moon, "A HighEfficiency PFM HalfBridge Converter Utilizing a HalfBridge LLC Converter Under Light Load Conditions," in IEEE, vol. 30, no. 9, pp , Sept [8] F. C. Lee, Q. Li, Z. Liu, Y. Yang, C. Fei and M. Mu, "Application of GaN devices for 1 kw server power supply with integrated magnetics," in CPSS and Applications, vol. 1, no. 1, pp. 312, Dec [9]. edl, N. O. Sokal and L. Balogh, "A novel softswitching fullbridge DC/DC converter: analysis, design considerations, and experimental results at 1.5 kw, 100 khz," in IEEE, vol. 6, no. 3, pp , July [10] H. Bai, Z. Nie and C. C. Mi, "Experimental Comparison of Traditional PhaseShift, DualPhaseShift, and ModelBased Control of Isolated Bidirectional DC DC Converters," in IEEE Transactions on Power Electronics, vol. 25, no. 6, pp , June [11] GwanBon Koo, GunWoo Moon and MyungJoong Youn, "New zerovoltageswitching phaseshift fullbridge converter with low conduction losses," in IEEE Transactions on Industrial Electronics, vol. 52, no. 1, pp , Feb [12] Bo Yang, F. C. Lee, A. J. Zhang and Guisong Huang, "LLC resonant converter for front end DC/DC conversion," APEC. Seventeenth Annual IEEE Applied Power Electronics Conference and Exposition (Cat. No.02CH37335), Dallas, TX, USA, 2002, pp vol.2. [13] D. Fu, F. C. Lee and S. Wang, "Investigation on transformer design of high frequency high efficiency dcdc converters," 2010 TwentyFifth Annual IEEE Applied Power Electronics Conference and Exposition (APEC), Palm Springs, CA, 2010, pp [14] Y. Yang, D. Huang, F. C. Lee and Q. Li, "Analysis and reduction of common mode EMI noise for resonant converters," 2014 IEEE Applied Power Electronics Conference and Exposition  APEC 2014, Fort Worth, TX, 2014, pp [15] Dianbo Fu, P. Kong, S. Wang, F. C. Lee and Ming Xu, "Analysis and suppression of conducted EMI emissions for frontend LLC resonant DC/DC converters," 2008 IEEE Power Electronics Specialists Conference, hodes, 2008, pp [16] B. Li, Q. Li, F. C. Lee and Y. Yang, "A symmetrical resonant converter and PCB transformer structure for common mode noise reduction," 2017 IEEE Energy Conversion Congress and Exposition (ECCE), Cincinnati, OH, 2017, pp [17] X. Huang, Z. Liu, Q. Li and F. C. Lee, "Evaluation and Application of 600 V GaN HEMT in Cascode Structure," in IEEE Transactions on Power Electronics, vol. 29, no. 5, pp , May [18] U. K. Mishra, P. Parikh and YiFeng Wu, "AlGaN/GaN HEMTsan overview of device operation and applications," in Proceedings of the IEEE, vol. 90, no. 6, pp , June [19] J. Millán, P. Godignon, X. Perpiñà, A. PérezTomás and J. ebollo, "A Survey of Wide Bandgap Power Semiconductor Devices," in IEEE, vol. 29, no. 5, pp , May [20] M. Mu and F. C. Lee, "Design and Optimization of a V High Frequency, HighCurrent LLC Converter With GaN Devices and Planar Matrix Transformers," in IEEE Journal of Emerging and Selected Topics in Power Electronics, vol. 4, no. 3, pp , Sept [21] B. Li, Q. Li and F. C. Lee, "A WBG based three phase 12.5 kw 500 khz CLLC resonant converter with integrated PCB winding transformer," 2018 IEEE Applied Power Electronics Conference and Exposition (APEC), San Antonio, TX, 2018, pp [22]. Chen, P. Brohlin and D. Dapkus, "Design and magnetics optimization of LLC resonant converter with GaN," 2017 IEEE Applied Power Electronics Conference and Exposition (APEC), Tampa, FL, 2017, pp [23] D. Huang, S. Ji and F. C. Lee, "LLC esonant Converter With Matrix Transformer," in IEEE, vol. 29, no. 8, pp , Aug [24] C. Fei, F. C. Lee and Q. Li, "HighEfficiency HighPowerDensity LLC Converter With an Integrated Planar Matrix Transformer for HighOutput Current Applications," in IEEE Transactions on Industrial Electronics, vol. 64, no. 11, pp , Nov [25] Y. C. Liu, C Chen, K. D. Chen, Y. L. Syu, M. C. Tsai, HighFrequency LLC esonant Converter with GaN Devices and Integrated Magnetics, Energies 2019, 12, [26] Y. Liu, C. Chen, K. Chen, Y. Syu and N. A. Dung, "HighFrequency and HighEfficiency Isolated TwoStage Bidirectional DCDC Converter for esidential Energy Storage Systems," in IEEE Journal of Emerging and Selected Topics in Power Electronics. [27] D. Huang, S. Ji and F. C. Lee, "Matrix transformer for LLC resonant converters," 2013 TwentyEighth Annual IEEE Applied Power Electronics Conference and Exposition (APEC), Long Beach, CA, 2013, pp [28] D. Huang, S. Ji and F. C. Lee, "LLC resonant converter with matrix transformer," 2014 IEEE Applied Power Electronics Conference and Exposition  APEC 2014, Fort Worth, TX, 2014, pp [29] B. Li, Q. Li and F. C. Lee, "HighFrequency PCB Winding Transformer With Integrated Inductors for a BiDirectional esonant Converter," in IEEE, vol. 34, no. 7, pp , July [30] M. K. anjram, I. Moon and D. J. Perreault, "VariableInverterectifier Transformer: A Hybrid Electronic and Magnetic Structure Enabling Adjustable High StepDown Conversion atios," in IEEE Transactions on Power Electronics, vol. 33, no. 8, pp , Aug. 2018, doi: /TPEL [31] Lloyd H. Dixon, Jr., "How to Design a Transformer with Fractional Turns." Unitrode/TI Magnetics Design Handbook [32] S. Li, E. ong, Q. Min and S. Lu, "A HalfTurn Transformer With Symmetry Magnetic Flux for HighFrequencyIsolated DC/DC Converters," in IEEE, vol. 33, no. 8, pp , Aug [33] E. ong, S. Li,. Zhang, X. Du, Q. Min and S. Lu, "A magnetic integration halfturn planar transformer for LLC resonant DCDC converters," 2018 IEEE Applied Power Electronics Conference and Exposition (APEC), San Antonio, TX, 2018, pp [34] Y. Liu et al., "QuarterTurn Transformer Design and Optimization for High Power Density 1MHz LLC esonant Converter," in IEEE Transactions on Industrial Electronics. [35] W. Feng, P. Mattavelli and F. C. Lee, "Pulsewidth Locked Loop (PWLL) for Automatic esonant Frequency Tracking in LLC DC DC Transformer (LLC DCX)," in IEEE, vol. 28, no. 4, pp , April [36] C. Fei, M. H. Ahmed, F. C. Lee and Q. Li, "TwoStage 48 V12 V/6 V 1.8 V Voltage egulator Module With Dynamic Bus Voltage Control for LightLoad Efficiency Improvement," in IEEE Transactions on Power Electronics, vol. 32, no. 7, pp , July [37] P. L. Dowell, "Effects of eddy currents in transformer windings," in Proceedings of the Institution of Electrical Engineers, vol. 113, no. 8, pp , August YuChen Liu (S 12 M 16 SM 20) received the M.S. degree and Ph.D. degree in Electronic and Computer Engineering from National Taiwan University of Science and Technology (NTUST), Taipei, Taiwan, in 2009 and 2015, respectively. He was a visiting researcher at the Future Energy Electronics Center, Virginia Tech., Blacksburg, USA, in From 2015 to 2016, he was a esearch Assistant Professor with the Department of Electronic Engineering, NTUST, for the Power Electronics Laboratory. He is currently an Associate Professor in the Department of Electrical Engineering at National Ilan University, Yilan, Taiwan. He earned the Young esearcher Award in 2018 from the National Science Council of Taiwan. He served as a faculty advisor for student teams of the IEEE International Future Energy Challenge, receiving awards in 2015, 2016, 2017, 2018 and He served as the Chair of the IEEE Industrial Applications Society (IAS) Taipei Chapter for
13 Chen Chen (S 16) was born in Taipei, Taiwan,.O.C, in He received the M.S degree in electronic engineering from National Taiwan University of Science and Technology, Taipei, Taiwan, in From 2019 to 2020, he was a visiting researcher at the Center for Power Electronics Systems (CPES), Virginia Tech., Blacksburg, VA, USA. He is currently working toward the Ph.D. degree at the same university. His research interests include zerovoltageswitching dcdc converter analysis and design, wide bandgap device applications, highfrequency converters, and high efficiency magnetic component design. power conversion. KaiDe Chen (S 18) was born in Tainan, Taiwan,.O.C, in He received the B.S degree in electronic engineering from National Taiwan University of Science and Technology, Taipei, Taiwan, in From 2019 to 2020, he was a visiting researcher at the Milan M. Jovanovic Power Electronics lab (MPEL)., Durham, NC, USA. He is currently working toward the Ph.D. degree by direct pursuit at the same university. His current research interests include resonant converters, wireless power transfer, wide bandgap device applications, and highfrequency YongLong Syu (S 18) was born in Tainan, Taiwan,.O.C, in He received the B.S degree in electronic engineering from National Taiwan University of Science and Technology, Taipei, Taiwan, in From 2019 to 2020, he was a visiting researcher at the Department of Electrical Engineering and Computer Sciences (EECS), UC Berkeley., Berkeley, CA, USA. He is currently working toward the Ph.D. degree by direct pursuit at the same university. His research interests include power factor correction, resonant converters, wide bandgap device applications, and highfrequency power conversion. MemberAtLarge for , and PELS Women in Engineering Chair in HuangJen Chiu (SM 09) has been with the Department of Electronic and Computer Engineering, National Taiwan University of Science and Technology (NTUST), Taipei, Taiwan, where he is a Distinguished Professor and the Director of Center for Power Electronic Technologies, now. Prof. Chiu also serves as the Dean of Industryacademia Collaboration at NTUST. His work brought him several distinctive awards including the Young esearcher Award in 2004 from the Ministry of Science and Technology, Taiwan, the Outstanding Teaching Awards in 2009 and 2017 and the Excellent esearch Award in 2009 and 2011 from the NTUST, the Y. Z. Hsu Scientific Paper Award in 2010, the Excellent Industryacademia Collaboration Award in 2015 and 2017, the Outstanding Industryacademia Collaboration Award in 2018 and Google Little Box Academic Awards. His student teams won the grand prize of the IEEE International Future Energy Challenge (IFEC) in 2013 and 2015, respectively and the 2018 IEEE Empower a Billion Lives (EBL) Pacific Asia egional Award. Dr. Chiu is an IEEE senior member and serves as an Associate Editor of the IEEE Transactions on Industry Applications. Dr. Chiu is actively working in IEEE Taipei Section. He arranged several meetings to promote the local activity of IEEE member in Taipei Section and to increase the number of IEEE membership in Taiwan. He served as the Chair of IEEE Industrial Electronics Society Taipei Chapter ( ), the General Cochair of 2017 IEEE International Future Energy Electronics Conference (IFEEC 2017ECCE Asia), the Program Chair of 2015 IEEE International Future Energy Electronics Conference (IEEE IFEEC 2015), the Topic CoChair of 2016 International Future Energy Challenge (IFEC 2016) and the Secretary of IEEE PELS/ IES Taipei Joint Chapter during Dr. Chiu is a Fellow of the Institute of Engineering and Technology (IET) and selected as the Distinguished Lecturer of IEEE Power Electronics Society ( and ). DeJia Lu was born in Taoyuan, Taiwan,.O.C, in He received the M.S degree in electronic engineering from National Taiwan University of Science and Technology, Taipei, Taiwan, in Since September 2019, he has been with 3Y Electronics, Inc., where he is currently an electronic engineer. His research interests include inverters, resonant converters, and wide bandgap device applications. Katherine A. Kim (S 06 M 14 SM 18) received the B.S. degree in electrical and computer engineering from Franklin W. Olin College of Engineering, Needham, MA, in She received the M.S. and Ph.D. degree in electrical and computer engineering from the University of Illinois, UrbanaChampaign, IL, USA, in 2011 and 2014, respectively. From 2014 to 2018, she was an Assistant Professor of Electrical and Computer Engineering at the Ulsan National Institute of Science and Technology (UNIST) in Ulsan, South Korea. Since 2019, she has been an Associate Professor of Electrical Engineering at National Taiwan University, Taipei, Taiwan. Her research focuses on power electronics and control for solar photovoltaic applications. Dr. Kim received the Graduate esearch Fellowship in 2011 from the U.S. National Science Foundation. She also received the Outstanding Teaching Award from UNIST in 2015, the ichard M. Bass Outstanding Young Power Electronics Engineer Award from the IEEE Power Electronics Society (PELS) in 2019, and recognition as an Innovator Under 35 for the Asia Pacific egion by the MIT Technology eview in Since 2017, she has served as an Associate Editor for the IEEE. For IEEE PELS, she served as the Student Membership Chair in , PELS
Cost effective resonant DCDC converter for hipower and wide load range operation.
Cost effective resonant DCDC converter for hipower and wide load range operation. Alexander Isurin(sashai@vanner.com) and Alexander Cook(alecc@vanner.com) Vanner Inc, Hilliard, Ohio Abstract This paper
More informationHighPowerDensity 400VDC19VDC LLC Solution with GaN HEMTs
HighPowerDensity 400VDC19VDC LLC Solution with GaN HEMTs Yajie Qiu, Lucas (Juncheng) Lu GaN Systems Inc., Ottawa, Canada yqiu@gansystems.com Abstract Compared to Silicon MOSFETs, GaN HighelectronMobility
More informationImprovements of LLC Resonant Converter
Chapter 5 Improvements of LLC Resonant Converter From previous chapter, the characteristic and design of LLC resonant converter were discussed. In this chapter, two improvements for LLC resonant converter
More informationA High Efficient Integrated Planar Transformer for PrimaryParallel Isolated Boost Converters
A High Efficient Integrated Planar Transformer for PrimaryParallel Isolated Boost Converters Gokhan Sen 1, Ziwei Ouyang 1, Ole C. Thomsen 1, Michael A. E. Andersen 1, and Lars Møller 2 1. Department of
More informationTYPICALLY, a twostage microinverter includes (a) the
3688 IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 33, NO. 5, MAY 2018 Letters Reconfigurable LLC Topology With Squeezed Frequency Span for HighVoltage BusBased Photovoltaic Systems Ming Shang, Haoyu
More informationA Novel Transformer Structure for High power, High Frequency converter
A Novel Transformer Structure for High power, High Frequency converter Chao Yan, Fan Li, Jianhong Zeng, Teng Liu, Jianping Ying Delta Power Electronics Center 238 Minxia Road, Caolu Industry Zone, Pudong,
More informationIN THE high power isolated dc/dc applications, full bridge
354 IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 21, NO. 2, MARCH 2006 A Novel ZeroCurrentTransition Full Bridge DC/DC Converter Junming Zhang, Xiaogao Xie, Xinke Wu, Guoliang Wu, and Zhaoming Qian,
More informationZCSPWM Converter for Reducing Switching Losses
IOSR Journal of Electrical and Electronics Engineering (IOSRJEEE) eissn: 22781676,pISSN: 23203331, Volume 9, Issue 1 Ver. III (Jan. 2014), PP 2935 ZCSPWM Converter for Reducing Switching Losses
More informationDesign of LowProfile Integrated Transformer and Inductor for SubstrateEmbedding in 15kW Isolated GaN DCDC Converters
Design of LowProfile Integrated Transformer and Inductor for SubstrateEmbedding in 15kW Isolated GaN DCDC Converters Haksun Lee, Vanessa Smet, P. M. Raj, Rao Tummala 3D Systems Packaging Research Center
More informationIN A CONTINUING effort to decrease power consumption
184 IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 14, NO. 1, JANUARY 1999 ForwardFlyback Converter with CurrentDoubler Rectifier: Analysis, Design, and Evaluation Results Laszlo Huber, Member, IEEE, and
More informationApplication of GaN Device to MHz Operating GridTied Inverter Using Discontinuous Current Mode for Compact and Efficient Power Conversion
IEEE PEDS 2017, Honolulu, USA 1215 December 2017 Application of GaN Device to MHz Operating GridTied Inverter Using Discontinuous Current Mode for Compact and Efficient Power Conversion Daichi Yamanodera
More informationA Novel SingleStage Push Pull Electronic Ballast With High Input Power Factor
770 IEEE TRANSACTIONS ON INDUSTRIAL ELECTRONICS, VOL. 48, NO. 4, AUGUST 2001 A Novel SingleStage Push Pull Electronic Ballast With High Input Power Factor ChangShiarn Lin, Member, IEEE, and ChernLin
More informationPage 1026
A New ZcsPwm FullBridge Dc Dc Converter With Simple Auxiliary Circuits Ramalingeswara Rao M 1, Mr.B,D.S.Prasad 2 1 PG Scholar, Pydah College of Engineering, Kakinada, AP, India. 2 Assistant Professor,
More informationDesign of a Dual Active Bridge DCDC Converter for Photovoltaic System Application. M.T. Tsai, C.L. Chu, Y.Z. Yang and D. R Wu
ICIC Express etters ICIC International c16 ISSN 185766 Volume 7, Number 8, August 16 pp. 185181 Design of a Dual Active Bridge DCDC Converter for Photovoltaic System Application M.T. Tsai, C.. Chu,
More informationENERGY saving through efficient equipment is an essential
IEEE TRANSACTIONS ON INDUSTRIAL ELECTRONICS, VOL. 61, NO. 9, SEPTEMBER 2014 4649 Isolated SwitchMode Current Regulator With Integrated Two Boost LED Drivers JaeKuk Kim, Student Member, IEEE, JaeBum
More informationDesign considerations for a Half Bridge LLC resonant converter
Design considerations for a Half Bridge LLC resonant converter Why an HB LLC converter Agenda Configurations of the HB LLC converter and a resonant tank Operating states of the HB LLC HB LLC converter
More informationdoi: info:doi/ /epe17ecceeurope
doi: info:doi/10.3919/epe17ecceeurope.017.8099085 Solution of Triple Problems in Transformer Windings for Current Resonant Converter with High Power Density and Wide Input ltage Range Seiya Abe (1), Toshiyuki
More informationA New Method for Startup of Isolated Boost Converters Using Magnetic and Winding Integration
Downloaded from orbit.dtu.dk on: Oct 06, 2018 A New Method for Startup of Isolated Boost Converters Using Magnetic and Winding Integration LindbergPoulsen, Kristian; Ouyang, Ziwei; Sen, Gokhan; Andersen,
More informationPrecise Analytical Solution for the Peak Gain of LLC Resonant Converters
680 Journal of Power Electronics, Vol. 0, No. 6, November 200 JPE 064 Precise Analytical Solution for the Peak Gain of LLC Resonant Converters SungSoo Hong, SangHo Cho, ChungWook Roh, and SangKyoo
More informationBIDIRECTIONAL dc dc converters are widely used in
816 IEEE TRANSACTIONS ON CIRCUITS AND SYSTEMS II: EXPRESS BRIEFS, VOL. 62, NO. 8, AUGUST 2015 HighGain ZeroVoltage Switching Bidirectional Converter With a Reduced Number of Switches Muhammad Aamir,
More informationSmall Signal Analysis for LLC Resonant Converter
Small Signal Analysis for LLC Resonant Converter Bo Yang and Fred C. Lee Center for Power Electronic Systems Bradley Department of Electrical and Computer Engineering Virginia Polytechnic Institute and
More informationA New Phase Shifted Converter using Soft Switching Feature for Low Power Applications
International OPEN ACCESS Journal Of Modern Engineering Research (IJMER A New Phase Shifted Converter using Soft Switching Feature for Low Power Applications Aswathi M. Nair 1, K. Keerthana 2 1, 2 (P.G
More informationA Color LED Driver Implemented by the Active Clamp Forward Converter
A Color LED Driver Implemented by the Active Clamp Forward Converter C. H. Chang, H. L. Cheng, C. A. Cheng, E. C. Chang * Power Electronics Laboratory, Department of Electrical Engineering IShou University,
More informationHigh frequency Soft Switching Half Bridge SeriesResonant DCDC Converter Utilizing Gallium Nitride FETs
Downloaded from orbit.dtu.dk on: Jun 29, 2018 High frequency Soft Switching Half Bridge SeriesResonant DCDC Converter Utilizing Gallium Nitride FETs Nour, Yasser; Knott, Arnold; Petersen, Lars Press
More informationDUAL BRIDGE LLC RESONANT CONVERTER WITH FREQUENCY ADAPTIVE PHASESHIFT MODULATION CONTROL FOR WIDE VOLTAGE GAIN RANGE
DUAL BRIDGE LLC RESONANT CONVERTER WITH FREQUENCY ADAPTIVE PHASESHIFT MODULATION CONTROL FOR WIDE VOLTAGE GAIN RANGE S M SHOWYBUL ISLAM SHAKIB ELECTRICAL ENGINEERING UNIVERSITI OF MALAYA KUALA LUMPUR,
More informationImproving Performance of High Speed GaN Transistors Operating in Parallel for High Current Applications
Improving Performance of High Speed GaN Transistors Operating in Parallel for High Current Applications David Reusch and Johan Strydom Efficient Power Conversion Corporation (EPC), El Segundo, CA, USA.
More informationA Bidirectional SeriesResonant Converter For Energy Storage System in DC Microgrids
IOSR Journal of Engineering (IOSRJEN) ISSN (e): 22503021, ISSN (p): 22788719 PP 0109 www.iosrjen.org A Bidirectional SeriesResonant Converter For Energy Storage System in DC Microgrids Limsha T M 1,
More informationR. W. Erickson. Department of Electrical, Computer, and Energy Engineering University of Colorado, Boulder
R. W. Erickson Department of Electrical, Computer, and Energy Engineering University of Colorado, Boulder 13.2.3 Leakage inductances + v 1 (t) i 1 (t) Φ l1 Φ M Φ l2 i 2 (t) + v 2 (t) Φ l1 Φ l2 i 1 (t)
More informationA Novel Bridgeless SingleStage HalfBridge AC/DC Converter
A Novel Bridgeless SingleStage HalfBridge AC/DC Converter WooYoung Choi 1, WenSong Yu, and JihSheng (Jason) Lai Virginia Polytechnic Institute and State University Future Energy Electronics Center
More informationA Bidirectional Resonant DCDC Converter for Electrical Vehicle Charging/Discharging Systems
A Bidirectional Resonant DCDC Converter for Electrical Vehicle Charging/Discharging Systems Fahad Khan College of Automation Engineering Nanjing University of Aeronautics and Astronautics, Nanjing 10016,
More informationWest Coast Magnetics. Advancing Power Electronics FOIL WINDINGS FOR SMPS INDUCTORS AND TRANSFORMERS. Weyman Lundquist, CEO and Engineering Manager
1 West Coast Magnetics Advancing Power Electronics FOIL WINDINGS FOR SMPS INDUCTORS AND TRANSFORMERS Weyman Lundquist, CEO and Engineering Manager TYPES OF WINDINGS 2 Solid wire Lowest cost Low DC resistance
More informationNOWADAYS, several techniques for highfrequency dc dc
IEEE TRANSACTIONS ON INDUSTRIAL ELECTRONICS, VOL. 54, NO. 5, OCTOBER 2007 2779 Voltage Oscillation Reduction Technique for PhaseShift FullBridge Converter KiBum Park, Student Member, IEEE, ChongEun
More informationMODELING AND SIMULATION OF LLC RESONANT CONVERTER FOR PHOTOVOLTAIC SYSTEMS
MODELING AND SIMULATION OF LLC RESONANT CONVERTER FOR PHOTOVOLTAIC SYSTEMS Shivaraja L M.Tech (Energy Systems Engineering) NMAM Institute of Technology Nitte, Udupi574110 Shivaraj.mvjce@gmail.com ABSTRACT
More informationAn Isolated DCAC Converter Module Integrating Renewable Energy Source and Energy Storage for Cascaded Inverter
An Isolated DCAC Converter Module Integrating Renewable Energy Source and Energy Storage for Cascaded Inverter Ritwik Chattopadhyay, Viju Nair. R, Subhashish Bhattacharya FREEDM Systems Center, Department
More informationHighPower DualInterleaved ZVS Boost Converter with Interphase Transformer for Electric Vehicles
HighPower DualInterleaved ZVS Boost Converter with Interphase Transformer for Electric Vehicles G. CalderonLopez and A. J. Forsyth School of Electrical and Electronic Engineering The University of Manchester
More informationHalf bridge converter with LCL filter for battery charging application using DCDC converter topology
Half bridge converter with LCL filter for battery charging application using DCDC converter topology Manasa.B 1, Kalpana S 2 Assistant Professor Department of Electrical and Electronics PESITM, Shivamogga
More informationCPES Power Management Consortium  with Extended Scope of Work
CPES Power Management Consortium  with Extended Scope of Work 1. Objectives Power Management Consortium (PMC) is an outgrowth of the VRM miniconsortium initiated in 1997. The goal is to extend its research
More informationA High Voltage Gain DCDC Boost Converter for PV Cells
Global Science and Technology Journal Vol. 3. No. 1. March 2015 Issue. Pp. 64 76 A High Voltage Gain DCDC Boost Converter for PV Cells Md. Al Muzahid*, Md. Fahmi Reza Ansari**, K. M. A. Salam*** and Hasan
More information25 Watt DC/DC converter using integrated Planar Magnetics
technical note 25 Watt DC/DC converter using integrated Planar Magnetics Philips Components 25 Watt DC/DC converter using integrated Planar Magnetics Contents Introduction 2 Converter description 3 Converter
More informationA HIGHLY EFFICIENT ISOLATED DCDC BOOST CONVERTER
A HIGHLY EFFICIENT ISOLATED DCDC BOOST CONVERTER 1 Aravind Murali, 2 Mr.Benny.K.K, 3 Mrs.Priya.S.P 1 PG Scholar, 2 Associate Professor, 3 Assistant Professor Abstract  This paper proposes a highly efficient
More informationNovel Passive Snubber Suitable for ThreePhase SingleStage PFC Based on an Isolated FullBridge Boost Topology
264 Journal of Power Electronics, Vol. 11, No. 3, May 2011 JPE 1133 Novel Passive Snubber Suitable for ThreePhase SingleStage PFC Based on an Isolated FullBridge Boost Topology Tao Meng, Hongqi Ben,
More informationHigh Frequency Soft Switching Of PWM Boost Converter Using Auxiliary Resonant Circuit
RESEARCH ARTICLE OPEN ACCESS High Frequency Soft Switching Of PWM Boost Converter Using Auxiliary Resonant Circuit C. P. Sai Kiran*, M. Vishnu Vardhan** * MTech (PE&ED) Student, Department of EEE, SVCET,
More informationPARALLELING of converter power stages is a wellknown
690 IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 13, NO. 4, JULY 1998 Analysis and Evaluation of Interleaving Techniques in Forward Converters Michael T. Zhang, Member, IEEE, Milan M. Jovanović, Senior
More informationMultitrack Power Factor Correction Architecture
Multitrack Power Factor Correction Architecture Minjie Chen, Sombuddha Chakraborty, David Perreault Princeton University Texas Instruments Massachusetts Institute of Technology 9781538611807/18/$31.00
More informationGenerating Isolated Outputs in a Multilevel Modular Capacitor Clamped DCDC Converter (MMCCC) for Hybrid Electric and Fuel Cell Vehicles
Generating Isolated Outputs in a Multilevel Modular Capacitor Clamped DCDC Converter (MMCCC) for Hybrid Electric and Fuel Cell Vehicles Faisal H. Khan 1, Leon M. Tolbert 2 1 Electric Power Research Institute
More informationCHAPTER 3. SINGLESTAGE PFC TOPOLOGY GENERALIZATION AND VARIATIONS
CHAPTER 3. SINGLESTAGE PFC TOPOLOG GENERALIATION AND VARIATIONS 3.1. INTRODUCTION The original DCM S 2 PFC topology offers a simple integration of the DCM boost rectifier and the PWM DC/DC converter.
More informationAnalysis and Design of a Bidirectional Isolated buckboost DCDC Converter with duel coupled inductors
Analysis and Design of a Bidirectional Isolated buckboost DCDC Converter with duel coupled inductors B. Ramu M.Tech (POWER ELECTRONICS) EEE Department Pathfinder engineering college Hanmakonda, Warangal,
More informationDCDC Transformer Multiphase Converter with Transformer Coupling for TwoStage Architecture
DCDC Transformer Multiphase Converter with Transformer Coupling for TwoStage Architecture M.C.Gonzalez, P.Alou, O.Garcia,J.A. Oliver and J.A.Cobos Centro de Electrónica Industrial Universidad Politécnica
More informationConventional SingleSwitch Forward Converter Design
Maxim > Design Support > Technical Documents > Application Notes > Amplifier and Comparator Circuits > APP 3983 Maxim > Design Support > Technical Documents > Application Notes > PowerSupply Circuits
More informationImpact of Fringing Effects on the Design of DCDC Converters
Impact of Fringing Effects on the Design of DCDC Converters Michael Seeman, Ph.D. Founder / CEO. 2018 APEC PSMA/PELS 2018. Outline Fringefield loss: What does a power supply designer need to know? Which
More informationMitigation of Common mode Noise for PFC Boost Converter by Balancing Technique
Mitigation of Common mode Noise for PFC Boost Converter by Balancing Technique Nasir *, Jon Cobb *Faculty of Science and Technology, Bournemouth University, Poole, UK, nasir@bournemouth.ac.uk, Faculty
More informationSIMULATION STUDIES OF HALFBRIDGE ISOLATED DC/DC BOOST CONVERTER
POZNAN UNIVE RSITY OF TE CHNOLOGY ACADE MIC JOURNALS No 80 Electrical Engineering 2014 Adam KRUPA* SIMULATION STUDIES OF HALFBRIDGE ISOLATED DC/DC BOOST CONVERTER In order to utilize energy from low voltage
More informationEfficiency Improvement of High Frequency Inverter for Wireless Power Transfer System Using a Series Reactive Power Compensator
IEEE PEDS 27, Honolulu, USA 25 December 27 Efficiency Improvement of High Frequency Inverter for Wireless Power Transfer System Using a Series Reactive Power Compensator Jun Osawa Graduate School of Pure
More informationA LLC RESONANT CONVERTER WITH ZERO CROSSING NOISE FILTER
A LLC RESONANT CONVERTER WITH ZERO CROSSING NOISE FILTER M. Mohamed Razeeth # and K. Kasirajan * # PG Research Scholar, Power Electronics and Drives, Einstein College of Engineering, Tirunelveli, India
More informationHigh Frequency Isolated Series Parallel Resonant Converter
Indian Journal of Science and Technology, Vol 8(15), DOI: 10.17485/ijst/2015/v8i15/52311, July 2015 ISSN (Print) : 09746846 ISSN (Online) : 09745645 High Frequency Isolated Series Parallel Resonant Converter
More informationSCIENCE & TECHNOLOGY
Pertanika J. Sci. & Technol. 25 (S): 918 (2017) SCIENCE & TECHNOLOGY Journal homepage: http://www.pertanika.upm.edu.my/ A Singlestage LED Driver with Voltage Doubler Rectifier Nurul Asikin, Zawawi 1
More informationIN recent years, the development of high power isolated bidirectional
IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 23, NO. 2, MARCH 2008 813 A ZVS Bidirectional DC DC Converter With PhaseShift Plus PWM Control Scheme Huafeng Xiao and Shaojun Xie, Member, IEEE Abstract The
More informationHybrid FullBridge HalfBridge Converter with Stability Network and Dual Outputs in Series
Hybrid FullBridge HalfBridge Converter with Stability Network and Dual Outputs in Series 1 Sowmya S, 2 Vanmathi K 1. PG Scholar, Department of EEE, Hindusthan College of Engineering and Technology, Coimbatore,
More informationMethods for Reducing Leakage Electric Field of a Wireless Power Transfer System for Electric Vehicles
Methods for Reducing Leakage Electric Field of a Wireless Power Transfer System for Electric Vehicles Masaki Jo, Yukiya Sato, Yasuyoshi Kaneko, Shigeru Abe Graduate School of Science and Engineering Saitama
More informationTHE converter usually employed for singlephase power
82 IEEE TRANSACTIONS ON INDUSTRIAL ELECTRONICS, VOL. 46, NO. 1, FEBRUARY 1999 A New ZVS Semiresonant High Power Factor Rectifier with Reduced Conduction Losses Alexandre Ferrari de Souza, Member, IEEE,
More information새로운무손실다이오드클램프회로를채택한두개의트랜스포머를갖는영전압스위칭풀브릿지컨버터
새로운무손실다이오드클램프회로를채택한두개의트랜스포머를갖는영전압스위칭풀브릿지컨버터 윤현기, 한상규, 박진식, 문건우, 윤명중한국과학기술원 ZeroVoltage Switching TwoTransformer FullBridge PWM Converter With Lossless DiodeClamp Rectifier H.K. Yoon, S.K. Han, J.S.
More informationImproved HighFrequency Planar Transformer for Line Level Control (LLC) Resonant Converters
Improved HighFrequency Planar Transformer for Line Level Control (LLC) Resonant Converters Author Water, Wayne, Lu, Junwei Published 2013 Journal Title IEEE Magnetics Letters DOI https://doi.org/10.1109/lmag.2013.2284767
More informationIN RECENT years, a number of singlestage input current
IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 21, NO. 5, SEPTEMBER 2006 1193 SingleStage Push Pull Boost Converter With Integrated Magnetics and Input Current Shaping Technique RongTai Chen and YungYaw
More informationEvaluation and Applications of 600V/650V EnhancementMode GaN Devices
Evaluation and Applications of 600V/650V EnhancementMode GaN Devices Xiucheng Huang, Tao Liu, Bin Li, Fred C. Lee, and Qiang Li Center for Power Electronics Systems, Virginia Tech Blacksburg, VA, USA
More informationTwooutput Class E Isolated dcdc Converter at 5 MHz Switching Frequency 1 Z. Pavlović, J.A. Oliver, P. Alou, O. Garcia, R.Prieto, J.A.
Twooutput Class E Isolated dcdc Converter at 5 MHz Switching Frequency 1 Z. Pavlović, J.A. Oliver, P. Alou, O. Garcia, R.Prieto, J.A. Cobos Universidad Politécnica de Madrid Centro de Electrónica Industrial
More informationMODERN switching power converters require many features
IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 19, NO. 1, JANUARY 2004 87 A ParallelConnected Single Phase Power Factor Correction Approach With Improved Efficiency Sangsun Kim, Member, IEEE, and Prasad
More informationBy Hiroo Sekiya, Chiba University, Chiba, Japan and Marian K. Kazimierzuk, Wright State University, Dayton, OH
ISSUE: November 2011 Core Geometry Coefficient For Resonant Inductors* By Hiroo Sekiya, Chiba University, Chiba, Japan and Marian K. Kazimierzuk, Wright State University, Dayton, OH A resonant inductor
More informationAn Extensive Input Voltage and FixedFrequency Single Stage Series Parallel LLC Resonant Converter for Dc Drive
Vol., Issue.5, SepOct. 0 pp36933698 ISSN: 496645 An Extensive Input Voltage and FixedFrequency Single Stage Series Parallel LLC Resonant Converter for Dc Drive P.Ganesh, T.Manokaran,.Department of
More informationCHAPTER 2 AN ANALYSIS OF LC COUPLED SOFT SWITCHING TECHNIQUE FOR IBC OPERATED IN LOWER DUTY CYCLE
40 CHAPTER 2 AN ANALYSIS OF LC COUPLED SOFT SWITCHING TECHNIQUE FOR IBC OPERATED IN LOWER DUTY CYCLE 2.1 INTRODUCTION Interleaving technique in the boost converter effectively reduces the ripple current
More informationA Dual Halfbridge Resonant DCDC Converter for Bidirectional Power Conversion
A Dual Halfbridge Resonant DCDC Converter for Bidirectional Power Conversion Mrs.Nagajothi Jothinaga74@gmail.com Assistant Professor Electrical & Electronics Engineering Sri Vidya College of Engineering
More informationDCtoDC Converter for Low Voltage Solar Applications
Proceedings of the th WSEAS International Conference on CIRCUITS, Agios Nikolaos, Crete Island, Greece, July 3, 7 4 DCtoDC Converter for Low Voltage Solar Applications K. H. EDELMOSER, H. ERTL Institute
More informationA LocalDimming LED BLU Driving Circuit for a 42inch LCD TV
A LocalDimming LED BLU Driving Circuit for a 42inch LCD TV YuCheol Park 1, HeeJun Kim 2, BackHaeng Lee 2, DongHyun Shin 3 1 YuCheol Park Intelligent Vehicle Technology R&D Center, KATECH, Korea
More informationThe Parallel Loaded Resonant Converter for the Application of DC to DC Energy Conversions
Available Online at www.ijcsmc.com International Journal of Computer Science and Mobile Computing A Monthly Journal of Computer Science and Information Technology IJCSMC, Vol. 3, Issue. 10, October 2014,
More informationComparing investigation for a Bidirectional Isolated DC/DC Converter using Series Voltage Compensation
Comparing investigation for a Bidirectional Isolated DC/DC Converter using Series Voltage Compensation Satoshi Miyawaki Nagaoka University of Technology Niigata, Japan miyawaki@stn.nagaokaut.ac.jp Junichi
More informationA New ZVS Bidirectional DCDC Converter With PhaseShift Plus PWM Control Scheme
A New ZVS Bidirectional DCDC Converter With PhaseShift Plus PWM Control Scheme Huafeng Xiao, Liang Guo, Shaojun Xie College of Automation Engineering,Nanjing University of Aeronautics and Astronautics
More informationResonant Converter Forreduction of Voltage Imbalance in a PMDC Motor
Resonant Converter Forreduction of Voltage Imbalance in a PMDC Motor Vaisakh. T Post Graduate, Power Electronics and Drives Abstract: A novel strategy for motor control is proposed in the paper. In this
More informationMiniaturized HighFrequency Integrated Power Conversion for Grid Interface
Massachusetts Institute of Technology Laboratory for Electromagnetic and Electronic Systems Miniaturized HighFrequency Integrated Power Conversion for Grid Interface David J. Perreault Seungbum Lim David
More informationElectromagnetic Interference Shielding Effects in Wireless Power Transfer using Magnetic Resonance Coupling for BoardtoBoard Level Interconnection
Electromagnetic Interference Shielding Effects in Wireless Power Transfer using Magnetic Resonance Coupling for BoardtoBoard Level Interconnection Sukjin Kim 1, Hongseok Kim, Jonghoon J. Kim, Bumhee
More informationChapter Three. Magnetic Integration for Multiphase VRMs
Chapter Three Magnetic Integration for Multiphase VRMs Integrated magnetic components are used in multiphase VRMs in order to reduce the number of the magnetics and to improve efficiency. All the magnetic
More informationLLC Resonant Converter for Battery Charging Application
International Journal of Electrical Engineering. ISSN 09742158 Volume 8, Number 4 (2015), pp. 379388 International Research Publication House http://www.irphouse.com LLC Resonant Converter for Battery
More informationAn Improved Single Input Multiple Output Converter
International Conference on Advanced Trends in Engineering and Technology04 (FORSCHUNG) 07 An Improved Single Input Multiple Output Parvathy and David E Abstract The aim of this study is to develop a
More informationR. W. Erickson. Department of Electrical, Computer, and Energy Engineering University of Colorado, Boulder
R. W. Erickson Department of Electrical, Computer, and Energy Engineering University of Colorado, Boulder 13.3.2 Lowfrequency copper loss DC resistance of wire R = ρ l b A w where A w is the wire bare
More informationSoftSwitching ActiveClamp Flyback Microinverter for PV Applications
SoftSwitching ActiveClamp Flyback Microinverter for PV Applications Rasedul Hasan, Saad Mekhilef, Mutsuo Nakaoka Power Electronics and Renewable Energy Research Laboratory (PEARL), Faculty of Engineering,
More informationClosed Loop Control of the Three Switch Serial Input Interleaved Forward Converter Fed Dc Drive
IOSR Journal of Electrical and Electronics Engineering (IOSRJEEE) eissn: 22781676,pISSN: 23203331, Volume 12, Issue 6 Ver. III (Nov. Dec. 2017), PP 7175 www.iosrjournals.org Closed Loop Control of
More informationShielding Effect of High Frequency Power Transformers for DC/DC Converters used in Solar PV Systems
Shielding Effect of High Frequency Power Transformers for DC/DC Converters used in Solar PV Systems Author Stegen, Sascha, Lu, Junwei Published 2010 Conference Title Proceedings of IEEE APEMC2010 DOI https://doiorg/101109/apemc20105475521
More informationSwitch Mode Power Supplies and their Magnetics
Switch Mode Power Supplies and their Magnetics Many factors must be considered by designers when choosing the magnetic components required in today s electronic power supplies In today s day and age the
More informationNovel ZeroCurrentSwitching (ZCS) PWM Switch Cell Minimizing Additional Conduction Loss
IEEE TRANSACTIONS ON INDUSTRIAL ELECTRONICS, VOL. 49, NO. 1, FEBRUARY 2002 165 Novel ZeroCurrentSwitching (ZCS) PWM Switch Cell Minimizing Additional Conduction Loss HangSeok Choi, Student Member, IEEE,
More informationTHE LLC resonant converter is becoming more and more
IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 27, NO. 8, AUGUST 2012 3775 A Universal Adaptive Driving Scheme for Synchronous Rectification in LLC Resonant Converters Weiyi Feng, Student Member, IEEE,FredC.Lee,
More informationApplication of GaN Devices for 1 kw Server Power Supply with Integrated Magnetics
CPSS TRANSACTIONS ON POWER ELECTRONICS AND APPLICATIONS, VOL. 1, NO. 1, DECEMBER 2016 3 Application of GaN Devices for 1 kw Server Power Supply with Integrated Magnetics Fred C. Lee, Qiang Li, Zhengyang
More informationA Study on Staggered Parallel DC/DC Converter Applied to Energy Storage System
International Core Journal of Engineering Vol.3 No.11 017 ISSN: 4141895 A Study on Staggered Parallel DC/DC Converter Applied to Energy Storage System Jianchang Luo a, Feng He b Chongqing University of
More informationThe Quest for High Power Density
The Quest for High Power Density Welcome to the GaN Era Power Conversion Technology Drivers Key design objectives across all applications: High power density High efficiency High reliability Low cost 2
More informationA New Soft Switching PWM DCDC Converter with Auxiliary Circuit and CentreTapped Transformer Rectifier
Available online at www.sciencedirect.com Procedia Engineering 53 ( 2013 ) 241 247 Malaysian Technical Universities Conference on Engineering & Technology 2012, MUCET 2012 Part 1 Electronic and Electrical
More informationPerformance Improvement of Bridgeless Cuk Converter Using Hysteresis Controller
International Journal of Electrical Engineering. ISSN 09742158 Volume 6, Number 1 (2013), pp. 110 International Research Publication House http://www.irphouse.com Performance Improvement of Bridgeless
More informationLLC Series Resonant Converter with PID Controller for Battery Charging Application
LLC Series Resonant Converter with PID Controller for Battery Charging Application M. Imran Shahzad, Shahid Iqbal, and Soib Taib School of Electrical & Electronic Engineering, Engineering Campus, Universiti
More informationSoftSwitching TwoSwitch Resonant AcDc Converter
SoftSwitching TwoSwitch Resonant AcDc Converter Aqulin Ouseph 1, Prof. Kiran Boby 2,, Prof. Dinto Mathew 3 1 PG Scholar,Department of Electrical and Electronics Engineering, Mar Athanasius College of
More informationHybrid Impedance Matching Strategy for Wireless Charging System
Hybrid Impedance Matching Strategy for Wireless Charging System TingEn Lee Automotive Research and Testing Center Research and Development Division Changhua County, Taiwan(R.O.C) leetn@artc.org.tw TzyyHaw
More informationWindings for High Frequency
Windings for High Frequency Charles R. Sullivan chrs@dartmouth.edu Dartmouth Magnetics and Power Electronics Research Group http://power.engineering.dartmouth.edu 1 The Issue The bestavailable technology
More informationA Double ZVSPWM ActiveClamping Forward Converter: Analysis, Design, and Experimentation
IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 16, NO. 6, NOVEMBER 2001 745 A Double ZVSPWM ActiveClamping Forward Converter: Analysis, Design, and Experimentation René TorricoBascopé, Member, IEEE, and
More informationAnnual Meeting. Task 4.8: DC Data Center with High Voltage isolation Virginia Tech Fred C Lee, Qiang Li and Shishuo Zhao.
Annual Meeting Task 4.8: DC Data Center with High Voltage isolation Virginia Tech Fred C Lee, Qiang Li and Shishuo Zhao January 17192017 December 8 2015 1 MV Utility Power Distribution in Data Center
More informationSepic Topology Based High StepUp Step down Soft Switching Bidirectional DCDC Converter for Energy Storage Applications
IOSR Journal of Electrical and Electronics Engineering (IOSRJEEE) eissn: 22781676,pISSN: 23203331, Volume 12, Issue 3 Ver. IV (May June 2017), PP 6876 www.iosrjournals.org Sepic Topology Based High
More information